If you have have any questions or concerns, please contact our Customer Service. If you have suggestions for upcoming events or links that should be included, please email them to me. Do not settle for less. Don a pair of safety glasses and poke a flat-bladed screwdriver in the furthest-away hole in each clip. F 30 61 065 Place hose 1 and additional wiring harness 2 in standard cable retainer 3 , as in the diagram. . Look to our excellent customer support for the largest selection and lowest pricing of quality Z3 parts.
Insert intensive windscreen cleaner pump 3 , and push it in to the rubber insert ring as far as it will go. F 30 61 077 Lay the additional wiring harness and hoses according to the diagram, and place in standard cable retainer 1. No content from this web site may be reproduced or copied in any form without the express written consent of David Cecil. One of my favorite places to shop for parts. Important: Do not operate the automatic cleaning system when the washer tanks are empty.
When installing: Tightening torque on fastening screws for impact pad is 5 Nm. Application information below is for reference only and should not be used to determine the exact vehicle fitment. Use Silver polish to gently clean the surface. Re-install all components in the reverse order to which they were removed, as appropriate. Exchanging windscreen wiper switch Take out all four Phillips screws 1 , and detach trim 2 from the base of the steering column.
There is an upper-centre clip with two tangs, spread these and pull on the carriage again and this will pop out. Move sound deadening out of the way. Re-Install all components in the reverse order to which they were removed, as appropriate. Pull the screwdriver down and towards you, this opens the clip and they will twang off: The glass can now be removed, stick it in the kitchen sink for a good clean unless you are sensibly replacing it. Install the standard windscreen washer pump at position 7. Turn ignition key to positon 1, and switch on parking light. Depress spring, twist contact ring 1 as far as it will go to the right or left, turn it back approx.
Insert the ad ditional wiring harness into the existing cable retainer 3. Warranties are for 2 year or 24,000 miles, Oembimmerparts. Turn the bracket in the direction of the arrow as far as it will go, and tighten the hex nuts. Cut hose 1 to size, and attach to distributor 3 , as in the diagram. We normally use express to do the shipment, 5-7 working days, the goods will arrive you. Important: Renew self-locking hex nut 2. Turn locks 1 through go0 , and remove battery cover 2.
F 30 61 064 Attach hose 1 of the headlight cleaning system to distributor 2 , as in the diagram. Attach the hoses to the headlight cleaning jets. Install intensive cleaner fluid tank 2 , and fix in position us ing hex screw 3 and washer 4. This worked well, no silvering came off and the results were good as new. F 30 61 076 Attach hose 1 of the headlight cleaning system to distributor 2 , as in the diagram. You will receive your first newsletter within 1-2 weeks. When Installing: Ensure that facia trim 2 is properly fitted in retaining clips 3.
De-burr the edges of the drilled hole, and coat with zinc powder paint. Attach hex nut 5 , and tighten. If you find the right part you want to order here, don't hesitate to email us. In my case reinstall all the stuff you didn't need to remove. Re-Install all parts removed from the passenger compart ment in the reverse order as appropriate. The appropriate software must then be obtained. If you need any help determining if this part works with your vehicle, please don't hesitate to contact us.
F 30 61 075 Insert sheet metal nut 1 into rib 2 on the combined tank. Side note, I really need to dehaze my headlights. Re-install all components in the reverse order to which they were removed, as appropriate. Could you please post a link or the name of that part? Important: Set down airbag unit only with plug side facing upwards, as in diagram. Insert all the washer pumps 5 , and push them into the rub ber insert rings as far as they will go. F 30 61 063 Attach plug 1 to control unit 2. F 30 61 049 Remove hex screw 1 form the earthing point at the front left of the engine compartment.
Does anybody know the deal with taking my 750I over to france with regards to the headlights? Secure the control unit using Phillips-head screw 3 and washer 4. Insert wiper motor 3 into bracket 4. Attach earth terminal 2 of the additional wiring harness at the earthing point. Then you gently guide the vent back into alignment with the switch, put on the knob to hold it while you push the vent back in. Important: Also screw on earth cable 4.